Engine
Engine Power - 1,600 rpm ISO 14396:2002
Engine Power - 1,600 rpm ISO 14396:2002
Engine Model
Gross Power - 1,600 rpm SAE J1995:2014
Gross Power - 1,600 rpm SAE J1995:2014
Net Power - 1,600 rpm ISO 9249:2007, SAE J1349:2011
Net Power - 1,600 rpm ISO 9249:2007, SAE J1349:2011
Engine Torque - 1,200 rpm ISO 14396:2002
Gross Torque - 1,200 rpm SAE J1995:2014
Net Torque - 1,200 rpm ISO 9249:2007, SAE J1349:2011
Displacement
Emissions
Meets U.S. EPA Tier 4 Final, EU Stage V, Korea Stage V, China Nonroad Stage IV and Japan 2014 emission standards.
Biodiesel Capability
Note (2)
¹Cat diesel engines are required to use ULSD (ultra-low sulfur diesel fuel with 15 ppm of sulfur or less) and are compatible* with ULSD blended with the following lower-carbon intensity fuels**up to:
20% biodiesel FAME (fatty acid methyl ester)
***100% renewable diesel, HVO (hydrotreated vegetable oil) and GTL (gas-to-liquid) fuels. Refer to guidelines for successful application.
Please consult your Cat dealer or "Caterpillar Machine Fluids Recommendations" (SEBU6250) for details.
*While Caterpillar engines are compatible with these alternative fuels, some regions may not allow their use.
**Tailpipe greenhouse gas emissions from lower-carbon intensity fuels are essentially the same as traditional fuels.
***Engines with no aftertreatment devices are compatible with higher blends, up to 100% biodiesel (for use of blends higher than 20% biodiesel, consult your Cat dealer).
Weights
Operating Weight
Note
Weight based on a machine configuration with Z-bar linkage, Bridgestone 26.5R25 VJT L3 radial tires, full fluids, operator, standard counterweight, ride control, cold start, roading fenders, Product Link™, front manual differential/open rear axles, powertrain guard, secondary steering, sound suppression, and a 4.2 m³ (5.5 yd³) general purpose bucket with BOCE.
Transmission
Forward - 1
Forward - 2
Forward - 3
Forward - 4
Reverse - 1
Reverse - 2
Reverse - 3
Reverse - 4
Note
Maximum travel speed in standard vehicle with empty bucket and standard L3 tires with 849 mm (33 in) roll radius.
Sound
Operator Sound Pressure Level - ISO 6396:2008
Exterior Sound Power Level - ISO 6395:2008
Operator Sound Pressure Level - ISO 6396:2008 ¹
Exterior Sound Power Level - ISO 6395:2008²
Note (1)
¹Including countries that adopt the EU and UK Directives.
Note (2)
²Exterior Sound Power Level - European Union Directive 2000/14/EC and UK Noise Regulation 2001 No. 1701.
Air Conditioning System
Air Conditioning
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a or R1234yf. See the label or instruction manual for identification of the gas.
- If equipped with R134a (Global Warming Potential = 1430), the system contains 1.600 kg (3.5 lb) of refrigerant, which has a CO2 equivalent of 2.288 metric tonnes (2.522 tons).
- If equipped with R1234yf (Global Warming Potential = 0.501), the system contains 1.389 kg (3.1 lb) of refrigerant, which has a CO2 equivalent of .001 metric tonnes (1.10 tons).
Operating Specifications
Static Tipping Load - Full 37° Turn
Static Tipping Load - Full 37° Turn - No Tire Deflection
Breakout Force
Note
For a machine configuration as defined under “Weight.”
Note (1)
Full compliance to ISO 14397-1:2007 Sections 1 thru 6, which requires 2% verification between calculations and testing.
Service Refill Capacities
Fuel Tank
DEF Tank
Cooling System
Crankcase
Transmission
Differential - Final Drives - Front
Hydraulic Tank
Hydraulic System
Implement System - Maximum Pump Output at 2,275 rpm
Implement System - Maximum Operating Pressure
Hydraulic Cycle Time - Total
Dimensions - Standard Lift
Height - Top of Hood
Height - Top of ROPS
Ground Clearance
Wheel Base
Overall Length - Without Bucket
Hinge Pin Height at Carry Height
Hinge Pin Height at Maximum Lift
Lift Arm Clearance at Maximum Lift
Rack Back - Maximum Lift
Rack Back - Carry Height
Width over Tires (Loaded)
Tread Width
Note
All dimensions are approximate and based on machine equipped with 4.2 m³ (5.5 yd³) general purpose bucket with BOCE and Bridgestone 26.5R25 VJT L3 radial tires.
Dimensions - High Lift
Height - Top of Hood
Height - Top of ROPS
Ground Clearance
Wheel Base
Overall Length - Without Bucket
Hinge Pin Height at Carry Height
Hinge Pin Height at Maximum Lift
Lift Arm Clearance at Maximum Lift
Rack Back - Maximum Lift
Rack Back - Carry Height
Width over Tires (Loaded)
Tread Width
Note
All dimensions are approximate and based on machine equipped with 4.2 m³ (5.5 yd³) general purpose bucket with BOCE and Bridgestone 26.5R25 VJT L3 radial tires.
Dimensions - Standard Lift
Rack Back - Maximum Lift
Dimensions - High Lift
Rack Back - Maximum Lift
Sound
With Cooling Fan Speed at Maximum Value - Note
Distance of 15 m (49.2 ft), moving forward in second gear ratio.
Dimensions - High Lift
Rack Back - Carry Height
Engine
Gross Torque @ 1,200 rpm – SAE J1995:2014
Engine Torque @ 1,200 rpm – ISO 14396:2002
Dimensions - High Lift
Rack Back at Ground
Engine
Note (3)
Cat diesel engines are required to use ULSD (ultra-low sulfur diesel fuel with 15 ppm of sulfur or less) or ULSD blended with the following lower-carbon intensity fuels up to: • 20% biodiesel FAME (fatty acid methyl ester)* • 100% renewable diesel, HVO (hydrogenated vegetable oil) and GTL (gas-to- liquid) fuels Refer to guidelines for successful application. Please consult your Cat dealer or “Caterpillar Machine Fluids Recommendations” (SEBU6250) for details. * Engines with no aftertreatment devices can use higher blends, up to 100% biodiesel.
Dimensions - Standard Lift
Rack Back - Carry Height
Rack Back at Ground
Engine
Displacement
Hydraulic System
Hydraulic Cycle Time - Total