Engine
Engine Model
Rated Engine Speed
Gross Power - SAE J1995:2014
Engine Power - ISO 14396:2002
Net Power - SAE J1349:2011
Net Power - SAE J1349:2011/ISO 9249:2007
Peak Torque - Speed
Net Torque
Bore
Stroke
Displacement
Note (1)
Power rating applies at 1,800 rpm when tested under the specified condition for the specified standard.
Note (2)
Net power advertised is the power available at the flywheel when the engine is equipped with fan at minimum speed, air intake system, exhaust system, and alternator.
Note (3)
Advertised power is tested per the specified standard in effect at the time of manufacture.
Note (4)
• No engine derating required up to 3048 m (10,000 ft). • Meets U.S. EPA Tier 4 Final and EU Stage V emission standards.
Emissions
Meets EU Stage V emission standards.
Weights - Approximate
Maximum Gross Vehicle Weight
Operating Specifications
Nominal Payload Class (100%)
Top Speed - Loaded
Target Payload (100%)
Maximum Working Payload (110%)
Maximum Allowable Payload (120%)*
Not to Exceed Payload (120%)*
Body Capacity - SAE 2:1
Note (1)
Capacity with Dual Slope body – no liner.
Note (2)
* Refer to the Caterpillar 10/10/20 Payload Policy for maximum gross machine weight limitations.
Transmission
Forward - 1
Forward - 2
Forward - 3
Forward - 4
Forward - 5
Forward - 6
Forward - 7
Reverse
Note
Maximum travel speeds with standard 24.00R35 (E4) tires.
Final Drives
Differential Ratio
Planetary Ratio
Total Reduction Ratio
Brakes
Brake Surface - Front
Brake Surface - Rear
Brake Standards
Body Hoists
Pump Flow - High Idle
Relief Valve Setting - Raise
Relief Valve Setting - Lower
Body Raise Time - High Idle
Body Lower Time - Float
Body Power Down - High Idle
Capacity - Dual Slope - 100% Fill Factor
Struck
Heaped (SAE 2:1)*
Note (1)
Contact your local Cat dealer for body recommendation.
Note (2)
Capacity - Flat Floor - 100% Fill Factor
Struck
Heaped (SAE 2:1)*
Note (1)
Contact your local Cat dealer for body recommendation.
Note (2)
Weight Distributions - Approximate
Front Axle - Empty
Front Axle - Loaded
Rear Axle - Empty
Rear Axle - Loaded
Suspension
Empty Loaded Cylinder Stroke Front
Empty Loaded Cylinder Stroke Rear
Rear Axle - Oscillation
Service Refill Capacities
Fuel Tank
Cooling System
Crankcase
Differential - Final Drives
Steering Tank
Steering System - Including Tank
Brake/Hoist Hydraulic Tank
Brake Hoist System
Torque Converter - Transmission System - HRC
Tires
Standard Tire
Note (1)
Productive capabilities of the 775G truck are such that, under certain job conditions, TKPH (TMPH) capabilities of standard or optional tires could be exceeded and, therefore, limit production.
Note (2)
Caterpillar recommends the customer evaluate all job conditions and consult the tire manufacturer for proper tire selection.
ROPS
ROPS Standards
Rollover Protective Structure (ROPS) for cab offered by Caterpillar meets ISO 3471:2008 ROPS criteria.
FOPS Standards
Falling Objects Protective Structure (FOPS) meets ISO 3449:2005 Level II FOPS criteria.
Sound
Sound Standards (1)
The operator Equivalent Sound Pressure Level (Leq) is 73 dB(A) when SAE J1166 FEB2008 is used to measure the value for an enclosed cab. This is a work cycle sound exposure level. The cab was properly installed and maintained. The test was conducted with the cab doors and the cab windows closed.
Sound Standards (2)
Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.
Sound Standards (3)
The machine sound power level is 114 dB(A), measured according to the test procedures and conditions specified in ISO 6395:2008 for the standard machine configuration. The measurement was conducted at 70% of the maximum engine cooling fan speed.
Steering
Steering Standards
Steer Angle
Turning Circle - Clearance Diameter
Turning Diameter - Front
Sustainability
Recyclability