Engine
Net Power
Engine Model
Bore
Stroke
Displacement
Emissions (U.S. EPA Tier 4 Final): Rated Speed
Emissions (Tier 2 Equivalent): Gross Power - SAE J1995
Emissions (U.S. EPA Tier 4 Final): Net Power - SAE J1995
Emissions (U.S. EPA Tier 4 Final): Net Power - SAE J1349
Emissions (Tier 2 Equivalent): Net Power - SAE J1349
Emissions (U.S. EPA Tier 4 Final): Peak Torque at 1,200 rpm - SAE J1995
Emissions (U.S. EPA Tier 4 Final): Gross Power - SAE J1995
Emissions (Tier 2 Equivalent): Peak Torque at 1,200 rpm - SAE J1995
Operating Specifications
Operating Weight
Bucket Capacity Range
Rated Payload - High Lift (Moderate to High Digging Resistance)
Rated Payload - Standard Lift (Moderate to High Digging Resistance)
Transmission
Transmission Type
Cat Planetary Power Shift
Forward - 1
Forward - 2
Forward - 3
Reverse - 1
Reverse - 2
Reverse - 3
Direct Drive - Forward 3
Direct Drive - Reverse 2
Direct Drive - Reverse 1
Direct Drive - Reverse 3
Direct Drive - Forward 2
Direct Drive - Forward 1
Hydraulic System - Lift/Tilt
Lift/Tilt System - Pump
Variable Displacement Piston
Maximum Flow at 1,850 rpm
Relief Valve Setting - Lift/Tilt
Lift Cylinder - Stroke
Lift/Tilt System - Circuit
Tilt Cylinder - Bore
Lift Cylinder - Bore
Hydraulic Cycle Times
Dump
Lower Float Down
Raise
Rack Back
Buckets
Bucket Capacities
Axles
Front
Rear
Oscillation Angle
Brakes
Brakes
Sound Performance
Operator Sound Pressure Level
The operator sound pressure level is 70 dB(A), measured according to the test procedures and conditions specified in ISO 6396:2008 for the standard machine configuration. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.
Hearing Protection
Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.
Machine Sound Power Level - Standard Machine Configuration
The machine sound power level is 116 dB(A), measured according to the test procedures and conditions specified in ISO 6395:2008 for the standard machine configuration. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.
Hydraulic System - Steering
Steering System - Circuit
Steering System - Pump
Piston, Variable Displacement
Maximum Flow at 1,350 rpm
Steering Cut Off Pressure
Hydraulic Cycle Times
Total Hydraulic Cycle Time
Service Refill Capacities
Fuel Tank
Transmission
Engine
Emissions (U.S. EPA Tier 4 Final): Gross Power - ISO 14396
Dimensions - High Lift - Approximate
Wheel Base
Ground to Lower Hitch Clearance
Rear Axle - Centerline to Bumper
Maximum Overall Height - Bucket Raised
Hydraulic System - Steering
Total Steering Angle
Dimensions - Standard Lift - Approximate
Ground to Top of ROPS
Ground to Top of Exhaust Stacks
Dump Angle at Maximum Lift
Service Refill Capacities
AC Oil
Dimensions - Standard Lift - Approximate
Ground to Bumper Clearance
Service Refill Capacities
Cooling Systems
Dimensions - High Lift - Approximate
Ground to Top of Exhaust Stacks
Service Refill Capacities
AC Refrigerant
Dimensions - Standard Lift - Approximate
Tread Width
Ground to Top of Hood
Dimensions - High Lift - Approximate
Rack Back Angle - Carry
Maximum Overall Length
Rack Back Angle - Ground Level
Engine
Torque Rise
Dimensions - High Lift - Approximate
Ground to Bumper Clearance
Ground to Center of Axles
Service Refill Capacities
Engine Crankcase
Dimensions - Standard Lift - Approximate
Ground to Lower Hitch Clearance
Operating Specifications
Operating Weight - Standard
Dimensions - High Lift - Approximate
Dump Angle at Maximum Lift
Ground to Top of ROPS
Hydraulic System - Lift/Tilt
Tilt Cylinder - Stroke
Service Refill Capacities
Differential - Final Drives - Front
Dimensions - High Lift - Approximate
Tread Width
Hydraulic System - Steering
Steering Cycle Times - High Idle
Service Refill Capacities
Differential - Final Drives - Rear
Operating Specifications
Operating Weight - High Lift
Dimensions - High Lift - Approximate
Clearance at 45° Dump (Tooth Tip)
Service Refill Capacities
Hydraulic System - Implement
Dimensions - Standard Lift - Approximate
Maximum Overall Length
Engine
Note (Tier 2 Equivalent) (2)
Rating for net power advertised is based on power available when the engine is equipped with alternator, air cleaner, muffler, and on-demand hydraulic fan drive at maximum fan speed.
Dimensions - Standard Lift - Approximate
B-Pin Height - Maximum Lift
Clearance at 50° Dump (Tooth Tip)
Engine
Note (Tier 4 Final) (1)
These ratings apply at 1,750 rpm when tested under the specified standard conditions.
Dimensions - Standard Lift - Approximate
Wheel Base
Rack Back Angle - Maximum Lift
Hydraulic System - Steering
Steering Cycle Times - Low Idle
Engine
Emissions (Tier 2 Equivalent): Gross Power - ISO 14396
Dimensions - High Lift - Approximate
Reach - Maximum Lift
Dimensions - Standard Lift - Approximate
Maximum Overall Height - Bucket Raised
Engine
Emissions (Tier 2 Equivalent): Rated Speed
Note (Tier 2 Equivalent) (1)
These ratings apply at 1,750 rpm when tested under the specified standard conditions.
Emissions (Tier 2 Equivalent): Net Power - SAE J1995
Service Refill Capacities
Hydraulic System - Steering
Dimensions - Standard Lift - Approximate
Rack Back Angle - Ground Level
Dimensions - High Lift - Approximate
Ground to Top of Hood
Dimensions - Standard Lift - Approximate
Rear Axle - Centerline to Bumper
Dimensions - High Lift - Approximate
B-Pin Height - Maximum Lift
Rack Back Angle - Maximum Lift
Dimensions - Standard Lift - Approximate
Rack Back Angle - Carry
Ground to Center of Axles
Reach - Maximum Lift
Engine
Note (Tier 4 Final) (2)
Rating for net power advertised is based on power available when the engine is equipped with alternator, air cleaner, muffler, and on-demand hydraulic fan drive at maximum fan speed.
Sound Performance
Machine Sound Power Level - Sound Suppressed Machine Configuration
The machine sound power level is 113 dB(A), measured according to the test procedures and conditions specified in ISO 6395:2008 for the sound suppressed machine configuration. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.