Engine
Net Power
Engine Model
Bore
Stroke
Displacement
Rated Speed
Peak Torque @ (speed) - SAE J1995
Net Power - SAE J1349
Torque Rise
Peak Power Speed - 1,500 rpm - Gross - ISO 14396
Emissions
U.S. EPA Tier 4 Final/EU Stage V
Peak Power Speed - 1,500 rpm - Gross - SAE J1995
Gross Power - ISO 14396
Peak Power Speed
Peak Power Speed - 1,500 rpm - Net Power - SAE J1349
Operating Specifications
Operating Weight
Rated Payload - Standard (Quarry Face)
Rated Payload - Loose Material (Standard)
Bucket Capacity Range
Transmission
Transmission Type
Cat switched reluctance electric drive
Forward 4 (virtual)
Reverse 3 (virtual)
Forward 2 (virtual)
Reverse 2 (virtual)
Forward 3 (virtual)
Reverse 1 (virtual)
Forward 1 (virtual)
Hydraulic System - Lift/Tilt
Lift Cylinder - Bore
Lift/Tilt System - Pump
Variable displacement piston
Lift/Tilt System - Circuit
EH-Positive Flow Control, Flow Sharing
Maximum Flow at 1,400-1,600 rpm
Lift Cylinder - Stroke
Relief Valve Setting - Lift/Tilt
Tilt Cylinder - Bore
Tilt Cylinder - Stroke
Service Refill Capacities
Fuel Tank
Transmission
Cooling System - Jacket Water
Differential - Final Drives - Rear
Cooling Systems - Power Train
Differential - Final Drives - Front
Engine Crankcase
Diesel Exhaust Fluid Tank
Hydraulic System - Implement/Steering
Buckets
Bucket Capacities
Axles
Front
Rear
Oscillation Angle
Brakes
Brakes
Hydraulic System - Steering
Steering Cycle Times - High Idle
Total Steering Angle
Maximum Flow at 1,400-1,600 rpm
Steering Cycle Times - Low Idle
Steering Cut Off Pressure
Steering System - Circuit
Steering System - Pump
Piston, variable displacement
Hydraulic Cycle Times
Rack Back
Raise
Lower Float Down
Total Hydraulic Cycle Time
Dump
Sound Performance - Tier 4 Final/Stage IV
Machine Sound Level (ISO 6395)
Operator Sound Level (ISO 6396)
Note (1)
The operator sound pressure level was measured according to the test procedures and conditions specified in ISO 6396:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.
Note (2)
Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.
Dimensions (Approximate) - Standard Lift
Rear Axle - Centerline to Bumper
Note
Specs are calculated with 6.9 m3 (9.0 yd3) rock bucket and Michelin XLDD2 with 978 mm (3.2 ft) centerline of rear axle height.
Dimensions (Approximate) - High Lift
Ground to Lower Hitch Clearance
Dimensions (Approximate) - Standard Lift
Maximum Overall Height - Bucket Raised
Dimensions (Approximate) - High Lift
B-Pin Height - Maximum Lift
Dimensions (Approximate) - Standard Lift
Ground to Top of ROPS
Dimensions (Approximate) - High Lift
Rear Axle - Centerline to Bumper
Clearance at Maximum Lift
Ground to Bumper Clearance
Ground to Top of Hood
Air Conditioning System
Air Conditioning
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.8 kg of refrigerant which has a CO2 equivalent of 2.574 metric tonnes.
Dimensions (Approximate) - Standard Lift
Ground to Top of Exhaust Stacks
Dimensions (Approximate) - High Lift
Front Axle Centerline to Bucket Tip
Ground to Top of Exhaust Stacks
Operating Specifications
Operating Weight - Standard
Dimensions (Approximate) - Standard Lift
Wheel Base
Dimensions (Approximate) - High Lift
Reach - Maximum Lift
Dimensions (Approximate) - Standard Lift
B-Pin Height - Maximum Lift
Dimensions (Approximate) - High Lift
Maximum Overall Length
Wheel Base
Dimensions (Approximate) - Standard Lift
Reach - Maximum Lift
Maximum Overall Length
Dimensions (Approximate) - High Lift
Ground to Top of ROPS
Service Refill Capacities
Note
All non-road Tier 4 Final/Stage IV diesel engines are required to use: – The machine has the flexibility to run on either ultra-low-sulfur diesel fuel (ULSD with 15 ppm of sulfur or less) or up to B20 biodiesel when feedstock meeting ASTM D7467 specifications is blended with ULSD. – Cat DEO-ULS™ or oils that meet the Cat ECF-3, API CJ-4, and ACEA E9 specifications are required. – Only use DEF that meets ISO 22241-1 standards.
Operating Specifications
Operating Weight - High Lift
Dimensions (Approximate) - Standard Lift
Ground to Bumper Clearance
Ground to Lower Hitch Clearance
Ground to Center of Axles
Hydraulic System - Steering
Steering
Dimensions (Approximate) - High Lift
Ground to Center of Axles
Dimensions (Approximate) - Standard Lift
Front Axle Centerline to Bucket Tip
Dimensions (Approximate) - High Lift
Note
Specs are calculated with 6.9 m3 (9.0 yd3) rock bucket and Michelin XLDD2 with 978 mm (3.2 ft) centerline of rear axle height.
Dimensions (Approximate) - Standard Lift
Clearance at Maximum Lift
Sound Performance - Tier 4 Final/Stage IV
Note (3)
The machine sound power level was measured according to the test procedures and conditions specified in ISO 6395:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.
Dimensions (Approximate) - High Lift
Maximum Overall Height - Bucket Raised
Operator's Cab
ROPS/FOPS
ROPS/FOPS meet ISO 3471:2008 and ISO 3449:2005 Level II standards
Dimensions (Approximate) - Standard Lift
Ground to Top of Hood