Engine
Net Power - SAE J1349
Engine Power - ISO 14396
Gross Power - SAE J1995
Engine Model
Peak Power Speed
Rated Speed
Emissions
U.S. EPA Tier 4 Final, EU Stage V, and Japan 2014
Bore
Stroke
Displacement
Peak Torque - 1,200 rpm
Torque Rise
Operating Specifications
Operating Weight
Rated Payload - Quarry Face
Rated Payload - Loose Material
Bucket Capacity Range
Cat Truck Match - Standard
Cat Truck Match - High Lift
Transmission
Transmission Type
Forward - 1
Forward - 2
Forward - 3
Forward - 4
Reverse - 1
Reverse - 2
Reverse - 3
Direct Drive - Forward 1
Direct Drive - Forward 2
Direct Drive - Forward 3
Direct Drive - Forward 4
Direct Drive - Reverse 1
Direct Drive - Reverse 2
Direct Drive - Reverse 3
Hydraulic System - Lift/Tilt
Lift/Tilt System - Circuit
EH- Positive Flow Control, Flow Sharing
Lift/Tilt System
Variable displacement piston
Maximum Flow at 1,400-1,860 rpm
Relief Valve Setting - Lift/Tilt
Cylinders, Double Acting - Lift, Bore and Stroke
210 mm × 1050 mm (8.7 in × 41.3 in)
Cylinders, Double Acting - Tilt, Bore and Stroke
269 mm × 685 mm (8.7 in × 27 in)
Pilot System
Variable displacement piston
Relief Valve Setting - Main
Hydraulic Cycle Time (1,400-1,860 rpm)
Rack Back
Raise
Dump
Lower Float Down
Total Hydraulic Cycle Time - Empty Bucket
Hydraulic System - Steering
Steering System - Circuit
Steering System - Pump
Piston, variable displacement
Maximum Flow
Relief Valve Setting - Steering
Total Steering Angle
Steering Cycle Times - High Idle
Steering Cycle Times - Low Idle
Air Conditioning System
Air Conditioning
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.8 kg of refrigerant which has a CO2 equivalent of 2.574 metric tonnes.
Axles
Front
Rear
Oscillation Angle
Brakes
Brakes
Operator's Cab
ROPS/FOPS
ROPS/FOPS meet ISO 3471:2008 and ISO 3449:2005 Level II standards
Service Refill Capacities
Fuel Tank
Cooling System
Coolant (Validated by Test Cell Fill Quantities)
Crankcase
Diesel Exhaust Fluid Tank
Transmission
Transmission - Validated by Test Cell Fill Quantities
Differential - Final Drives - Front
Differential - Final Drives - Rear
Hydraulic System Factory Fill
Hydraulic System - Tank Only
Sound Performance - Tier 4 Final/EU Stage V - Standard
Operator Sound Level (ISO 6396)
Machine Sound Level (ISO 6395)
Note (1)
The operator sound pressure level was measured according to the test procedures and conditions specified in ISO 6396:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.
Note (2)
Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.
Dimensions (Approximate) - Standard Lift Linkage
Ground to Top of ROPS
Ground to Top of Exhaust Stacks
Ground to Top of Hood
Rear Axle - Centerline to Bumper
Front Axle Centerline to Bucket Tip
Wheel Base
Maximum Overall Length
Ground to Lower Hitch Clearance
Clearance at Maximum Lift
B-Pin Height - Maximum Lift
Maximum Overall Height - Bucket Raised
Reach - Maximum Lift
Dimensions (Approximate) - High Lift Linkage
Ground to Top of ROPS
Ground to Top of Exhaust Stacks
Ground to Top of Hood
Rear Axle - Centerline to Bumper
Front Axle Centerline to Bucket Tip
Wheel Base
Maximum Overall Length
Ground to Lower Hitch Clearance
Clearance at Maximum Lift
B-Pin Height - Maximum Lift
Maximum Overall Height - Bucket Raised
Reach - Maximum Lift
Buckets
Bucket Capacities
Standard Equipment
NOTE
ELECTRICAL
OPERATOR ENVIRONMENT
POWER TRAIN
OTHER
Optional Equipment
NOTE
POWER TRAIN
OPERATOR ENVIRONMENT
ADDITIONAL EQUIPMENT
OTHER OPTIONAL CONFIGURATIONS