Engine
Engine Model
Flywheel Power
Bore
Stroke
Displacement
Emissions
Engine Power - Gross SAE J1995*
Engine Power - ISO 14396
Engine Power - Net SAE J1349/ISO 9249
Net SAE J1349/ISO 9249
Weights
Operating Weight
Shipping Weight
Operating Weight - CD
Shipping Weight - CD
Transmission
1 Forward
2 Forward
3 Forward
1 Reverse
2 Reverse
3 Reverse
Type
Transmission Clutch Diameter
Hydraulic Controls
D11T - Bulldozer Relief Valve Setting
D11T - Combined Pump Output - Implement
D11T - Pump Type
D11T - Ripper (Lift) Relief Valve Setting
D11T - Ripper (Pitch) Relief Valve Setting
D11T - Tilt Cylinder Relief Valve Setting
D11T - Tilt Pump Flow
D11T CD - Carrydozer Relief Valve Setting
D11T CD - Pump Output - Implement
D11T CD - Pump Type
D11T CD - Ripper (Lift) Relief Valve Setting
D11T CD - Ripper (Pitch) Relief Valve Setting
D11T CD - Tilt Cylinder Flow
D11T CD - Tilt Cylinder Relief Valve Setting
Undercarriage
Shoe Type
Width - Shoe
Shoes/Side
Grouser Height
Pitch
Track Gauge
Length - Track on Ground
Ground Contact Area
Track Rollers/Side
Number of Carrier Rollers
Ground Clearance*
Ground Contact Area - CD
Width - Shoe - CD
Service Refill Capacities
Fuel Tank
Cooling System
Engine Crankcase*
Power Train
Final Drive - Each
Roller Frames - Each
Pivot Shaft Compartment
Implement Hydraulic System - Tank Only
Fuel Tank - High Capacity
Track Roller Frame
Oscillation
Steering and Brakes
Hydraulically Applied Multiple-disc Steering Clutch
Spring Applied Multiple-disc Brake
Standards
FOPS
Falling Objects Protective Structure (FOPS) meets the following criteria: ISO 3449:2005 LEVEL II.
ROPS
Rollover Protective Structure (ROPS) meets the following criteria: SAE J1040 MAY94, ISO 3471:1994.
Dimensions (Approximate) - D11T
Drawbar Height (Center of Clevis)*
Ground Clearance*
Height - FOPS Cab*
Height - ROPS/Canopy*
Height - Top of Stack*
Length - Basic Tractor - With Drawbar
Length - Track on Ground
Length - With Multi-Shank Ripper
Length - With SU-Blade
Length - With Single-Shank Ripper
Length - With U-Blade
Note (1)
*Includes grouser height for total dimensions on hard surfaces.
Note (2)
D11T shown equipped with 710 mm (28 in) shoes.
Overall Length - Basic Tractor
Overall Length - SU-Blade/SS Ripper
Track Gauge
Width - Over Trunnions
Width - Without Trunnions - Standard Shoe
Dimensions (Approximate) - D11T CD
Drawbar Height (Center of Clevis)*
Ground Clearance*
Height - FOPS Cab*
Height - ROPS/Canopy*
Height - Top of Stack*
Length - Basic Tractor - With Drawbar
Length - Track on Ground
Length - With Multi-Shank Ripper
Length - With SU-Blade**
Length - With Single-Shank Ripper
Note (1)
*Includes grouser height for total dimensions on hard surfaces.
Note (2)
Note (3)
D11T shown equipped with 710 mm (28 in) shoes.
Overall Length - Basic Tractor
Overall Length - SU-Blade/SS Ripper**
Track Gauge
Width - Over Trunnions
Width - Without Trunnions - Standard Shoe
Engine
Note (1)
* Excludes all fan losses.
Note (2)
Engine ratings apply at 1,800 rpm.
Note (3)
Net power advertised is the power available at the flywheel when the engine is equipped with air cleaner, muffler, alternator, fan, and engine emissions controls as required.
Note (4)
No derating required up to 3658 m (12,000 ft) altitude. High altitude attachment available for greater than 3658 m (12,000 ft).
Hydraulic Controls
Note (1)
Pump output measured at 1,800 engine rpm and 6895 kPa (1,000 psi).
Note (2)
Electro-hydraulic pilot valves assist operations of ripper and dozer controls.
Note (3)
Complete system consists of pump, tank with filter, oil cooler, valves, lines, and control levers.
Service Refill Capacities
Fuel Tank - Platform Ready
Note
Standards
Sound (1)
The operator Equivalent Sound Pressure Level (Leq) is 79 dB(A) when ISO 6396:2008 is used to measure the value for an enclosed cab. This is a dynamic cycle sound exposure level. The cab was properly installed and maintained. The test was conducted with th
Sound (2)
The exterior sound pressure level for the standard machine measured at a distance of 15 m (49.2 ft) according to the test procedures specified in SAE J88 APR95, mid-gear-moving operation, is 87 dB(A).
Undercarriage
Note (1)
* Includes grouser height for total dimensions on hard surface.
Note (2)
Sleeve Bearing Track with Positive Pin Retention.
Weights
Note (1)
D11T Operating Weight: Includes blade tilt cylinders, coolant, lubricants, full fuel tank, ROPS, FOPS cab, 11U ABR bulldozer, single-shank ripper with pin-puller, fast fuel, 710 mm (28 in) ES shoes, and operator.
Note (2)
D11T Shipping Weight: Base machine chassis with cab and pivot shaft. Doesn't include ROPS, ripper, blade, track, or roller frames.
Note (3)
D11T CD Operating Weight: Includes lubricant, coolant, full fuel tank, 915 mm (36 in) extreme service shoes, 11 Carrydozer, single-shank ripper, and operator.
Note (4)
D11T CD Shipping Weight: Base machine chassis with cab and pivot shaft. Doesn't include ROPS, ripper, blade, track, or roller frames.